咨询热线:0769-88411070
联系方式

河源市生兴行石化有限公司东莞分公司

Tel: (0769)8841 1828

Fax:(0769)8841 2938

客服联系方式

E-mail: jookalin@shhcl.com.hk

Wechat: jooka15

Tel: (0769)8841 1828 - 224

林先生



联系我们

河源市生兴行石化有限公司东莞分公司
电话:(86)0769-8841 1070
传真:(86)0769-8841 2938
地址:广东省东莞市中堂镇北潢公路旁(中堂车站斜对面)

 
Isopar L MSDS-EN
 

 

SAFETY DATA SHEET

 

SECTION 1

 PRODUCT AND COMPANY IDENTIFICATION

 

PRODUCT

Product Name:    ISOPAR L FLUID

Product Description:       Isoparaffinic Hydrocarbon

             

Recommended Use:         Aerosol, Cleaning fluid, Diluent, Metal processing fluid, Polymerization fluid, Process fluid, Viscosity modifier

 

 

 

COMPANY IDENTIFICATION

 

Country

Supplier (company name / address / phone)

24 Hour Environmental / Health Emergency Telephone Number

China

Sang Hing Hong Chemicals Ltd.DongGuan Branch

Correspondence address:

Beihuang Roadside

Zhongtang Town

Dongguan Guangdong, China 523233

 

(+86) 0769-88411828

(+86) 0769-88411828

China/Hong Kong

Sang Hing Hong Chemicals Ltd.

Units 806-807,Level 8 Metroplaza,Tower II,223 Hing Fong Road,Kwai Fong,N.T.,Hong Kong

 

(+852) 2494 8222

HK:(+852) 2494 8222

 

 SECTION 2

 HAZARDS IDENTIFICATION

 

The hazard classification for this material is in accordance with the General Rules for Classification and Hazard Communication of Chemicals (GB 13690-2009).

 

CLASSIFICATION:

 

  Flammable liquid: Category 4.

  Aspiration toxicant: Category 1.

 

LABEL:

Symbol:

 

Signal Word:  Danger

 

Hazard Statements:

 

  Physical:  H227:  Combustible liquid.

  Health:  H304:  May be fatal if swallowed and enters airways.   

 

Precautionary Statements:

 

  Prevention:  P210:  Keep away from flames and hot surfaces.  No smoking.  P280: Wear protective gloves and eye / face protection.

  Response:  P301 + P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.  P331:  Do NOT induce vomiting.  P370 + P378: In case of fire:  Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish.

  Storage:  P403 + P235: Store in a well-ventilated place. Keep cool.  P405:  Store locked up.

  Disposal:  P501: Dispose of contents and container in accordance with local regulations.

 

Contains: NAPHTHA (PETROLEUM), HYDROTREATED HEAVY

 

Other hazard information:

 

 

PHYSICAL / CHEMICAL HAZARDS

 Material can accumulate static charges which may cause an ignition.  Material can release vapours that readily form flammable mixtures. Vapour accumulation could flash and/or explode if ignited.  Combustible.

 

HEALTH HAZARDS

 May be irritating to the eyes, nose, throat, and lungs.  Repeated exposure may cause skin dryness or cracking.

 

ENVIRONMENTAL HAZARDS

 No significant hazards.

 

 

NOTE:   This material should not be used for any other purpose than the intended use in Section 1 without expert advice. Health studies have shown that chemical exposure may cause potential human health risks which may vary from person to person.

 

SECTION 3

 COMPOSITION / INFORMATION ON INGREDIENTS

 

This material is defined as a complex substance.

 

Hazardous Substance(s) or Complex Substance(s) required for disclosure

 Name

 CAS#

 Concentration*

GHS Hazard Codes

NAPHTHA (PETROLEUM), HYDROTREATED HEAVY

 64742-48-9

 100 %

 H227, H304

   

 * All concentrations are percent by weight unless ingredient is a gas. Gas concentrations are in percent by volume.  Concentration values may vary.

 

 SECTION 4

 FIRST AID MEASURES

 

INHALATION

Remove from further exposure.  For those providing assistance, avoid exposure to yourself or others.  Use adequate respiratory protection.  If respiratory irritation, dizziness, nausea, or unconsciousness occurs, seek immediate medical assistance.  If breathing has stopped, assist ventilation with a mechanical device or use mouth-to-mouth resuscitation.

 

SKIN CONTACT

Wash contact areas with soap and water.  Remove contaminated clothing.  Launder contaminated clothing before reuse.

 

EYE CONTACT

Flush thoroughly with water.  If irritation occurs, get medical assistance.

 

INGESTION

Seek immediate medical attention.  Do not induce vomiting.

 

NOTE TO PHYSICIAN

If ingested, material may be aspirated into the lungs and cause chemical pneumonitis.  Treat appropriately.

 

 

 

SECTION 5

FIRE FIGHTING MEASURES

 

EXTINGUISHING MEDIA

Appropriate Extinguishing Media:  Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.

 

Inappropriate Extinguishing Media:  Straight streams of water

 

FIRE FIGHTING

Fire Fighting Instructions:  Evacuate area.  Prevent run-off from fire control or dilution from entering streams, sewers or drinking water supply.  Fire-fighters should use standard protective equipment and in enclosed spaces, self-contained breathing apparatus (SCBA).  Use water spray to cool fire exposed surfaces and to protect personnel.

 

Unusual Fire Hazards:  Combustible.

 

Hazardous Combustion Products:   Incomplete combustion products, Oxides of carbon, Smoke, Fume

 

FLAMMABILITY PROPERTIES

Flash Point [Method]:  61 C (142 F) - 66 C  (151 F)

Flammable Limits (Approximate volume % in air):   LEL:  0.7     UEL: 5.3

Autoignition Temperature:   >200 C  (392 F)

 

 SECTION 6

ACCIDENTAL RELEASE MEASURES

 

 

NOTIFICATION PROCEDURES

In the event of a spill or accidental release, notify relevant authorities in accordance with all applicable regulations.

 

PROTECTIVE MEASURES

Avoid contact with spilled material.  Warn or evacuate occupants in surrounding and downwind areas if required, due to toxicity or flammability of the material.  See Section 5 for fire fighting information.  See the Hazard Identification Section for Significant Hazards.  See Section 4 for First Aid Advice.  See Section 8 for advice on the minimum requirements for personal protective equipment. Additional protective measures may be necessary, depending on the specific circumstances and/or the expert judgment of the emergency responders.

 

For emergency responders:  Respiratory protection: half-face or full-face respirator with filter(s) for organic vapor and, when applicable, H2S, or Self Contained Breathing Apparatus (SCBA) can be used depending on the size of spill and potential level of exposure.  If the exposure cannot be completely characterized or an oxygen deficient atmosphere is possible or anticipated, SCBA is recommended.  Work gloves that are resistant to aromatic hydrocarbons are recommended.  Note: gloves made of polyvinyl acetate (PVA) are not water-resistant and are not suitable for emergency use.  Chemical goggles are recommended if splashes or contact with eyes is possible.  Small spills: normal antistatic work clothes are usually adequate.  Large spills: full body suit of chemical resistant, antistatic material is recommended.

 

SPILL MANAGEMENT

Land Spill:  Eliminate all ignition sources (no smoking, flares, sparks or flames in immediate area).  Stop leak if you can do so without risk.  All equipment used when handling the product must be grounded.  Do not touch or walk through spilled material.  Prevent entry into waterways, sewer, basements or confined areas.  A vapour-suppressing foam may be used to reduce vapour.  Use clean non-sparking tools to collect absorbed material.  Absorb or cover with dry earth, sand or other non-combustible material and transfer to containers.  Large Spills:  Water spray may reduce vapour, but may not prevent ignition in enclosed spaces.  Recover by pumping or with suitable absorbent.

 

Water Spill:  Stop leak if you can do so without risk.  Confine the spill immediately with booms.  Warn other shipping.  Remove from the surface by skimming or with suitable absorbents.  Seek the advice of a specialist before using dispersants.

 

Water spill and land spill recommendations are based on the most likely spill scenario for this material; however, geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction and speed may greatly influence the appropriate action to be taken.  For this reason, local experts should be consulted.  Note:  Local regulations may prescribe or limit action to be taken.

 

ENVIRONMENTAL PRECAUTIONS

Large Spills: Dike far ahead of liquid spill for later recovery and disposal.  Prevent entry into waterways, sewers, basements or confined areas.

 

 

 SECTION 7

HANDLING AND STORAGE

 

HANDLING

Avoid contact with skin. Small metal particles from machining may cause abrasion of the skin and may predispose to dermatitis.  Prevent small spills and leakage to avoid slip hazard. Material can accumulate static charges which may cause an electrical spark (ignition source).  When the material is handled in bulk, an electrical spark could ignite any flammable vapors from liquids or residues that may be present (e.g., during switch-loading operations).  Use proper bonding and/or earthing procedures.  However, bonding and earthing may not eliminate the hazard from static accumulation.  Consult local applicable standards for guidance.  Additional references include American Petroleum Institute 2003 (Protection Against Ignitions Arising out of Static, Lightning and Stray Currents) or National Fire Protection Agency 77 (Recommended Practice on Static Electricity) or CENELEC CLC/TR 50404 (Electrostatics - Code of practice for the avoidance of hazards due to static electricity).

 

Loading/Unloading Temperature:     [Ambient]

 

Transport Temperature:     [Ambient]

Transport Pressure:     [Ambient]

 

Static Accumulator:   This material is a static accumulator.  A liquid is typically considered a nonconductive, static accumulator if its conductivity is below 100 pS/m (100x10E-12 Siemens per meter) and is considered a semiconductive, static accumulator if its conductivity is below 10,000 pS/m.  Whether a liquid is nonconductive or semiconductive, the precautions are the same.  A number of factors, for example liquid temperature, presence of contaminants, anti-static additives and filtration can greatly influence the conductivity of a liquid.

 

STORAGE

 The  type of container used to store the material may affect static accumulation and dissipation.  Keep container closed. Handle containers with care. Open slowly in order to control possible pressure release.  Store in a cool, well-ventilated area.  Storage containers should be earthed and bonded.  Fixed storage containers, transfer containers and associated equipment should be grounded and bonded to prevent accumulation of static charge.

Storage Temperature:       [Ambient]

Storage Pressure:     [Ambient]

 

Suitable Containers/Packing:   Drums; Tank Trucks; Barges; Railcars

Suitable Materials and Coatings (Chemical Compatibility):   Carbon Steel; Stainless Steel; Polyester; Teflon; Polyethylene; Polypropylene

Unsuitable Materials and Coatings:   Butyl Rubber; Polystyrene; Ethylene-proplyene-diene monomer (EPDM); Natural Rubber  

 

 SECTION 8

 EXPOSURE CONTROLS / PERSONAL PROTECTION

 

EXPOSURE LIMIT VALUES

 

Exposure limits/standards (Note: Exposure limits are not additive)

 

 Substance Name

Form

Limit/Standard

Note

Source

Year

NAPHTHA (PETROLEUM), HYDROTREATED HEAVY

Vapour.

RCP - TWA

1200 mg/m3

171 ppm

Total Hydrocarbons

ExxonMobil

2009

     

 

 

 

NOTE: Limits/standards shown for guidance only.  Follow applicable regulations.

 

ENGINEERING CONTROLS

 

The level of protection and types of controls necessary will vary depending upon potential exposure conditions. Control measures to consider:

 Adequate ventilation should be provided so that exposure limits are not exceeded.  Use explosion-proof ventilation equipment.

 

PERSONAL PROTECTION

 

Personal protective equipment selections vary based on potential exposure conditions such as applications, handling practices, concentration and ventilation.  Information on the selection of protective equipment for use with this material, as provided below, is based upon intended, normal usage.

 

Respiratory Protection:   If engineering controls do not maintain airborne contaminant concentrations at a level which is adequate to protect worker health, an approved respirator may be appropriate.  Respirator selection, use, and maintenance must be in accordance with regulatory requirements, if applicable.  Types of respirators to be considered for this material include:

 Half-face filter respirator  Type A filter material.

 

For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode.  Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate, gas/vapour warning properties are poor, or if air purifying filter capacity/rating may be exceeded.

 

Hand Protection:   Any specific glove information provided is based on published literature and glove manufacturer data.  Glove suitability and breakthrough time will differ depending on the specific use conditions. Contact the glove manufacturer for specific advice on glove selection and breakthrough times for your use conditions. Inspect and replace worn or damaged gloves. The types of gloves to be considered for this material include:

 If prolonged or repeated contact is likely, chemical-resistant gloves are recommended.  If contact with forearms is likely, wear gauntlet-style gloves.  Nitrile

 

Eye Protection:   If contact is likely, safety glasses with side shields are recommended.

 

Skin and Body Protection:    Any specific clothing information provided is based on published literature or manufacturer data.  The types of clothing to be considered for this material include:

 If prolonged or repeated contact is likely, chemical, and oil resistant clothing is recommended.

 

Specific Hygiene Measures:   Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking.  Routinely wash work clothing and protective equipment to remove contaminants.  Discard contaminated clothing and footwear that cannot be cleaned. Practice good housekeeping.

 

 

ENVIRONMENTAL CONTROLS

 Comply with applicable environmental regulations limiting discharge to air, water and

soil. Protect the environment by applying appropriate control measures to prevent or limit

emissions.

 

 

SECTION 9

 PHYSICAL AND CHEMICAL PROPERTIES

 

Note:  Physical and chemical properties are provided for safety, health and environmental considerations only and may not fully represent product specifications.  Contact the Supplier for additional information.

 

GENERAL INFORMATION

Physical State:    Liquid

Form:    Clear

Colour:   Colourless

Odour:   Mild Petroleum/Solvent

Odour Threshold:   N/D

 

IMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATION

Relative Density:   N/D 

Density (at 15 ºC):   776 kg/m³ (6.48 lbs/gal, 0.78 kg/dm³)

Flash Point [Method]:     61 C (142 F) - 66 C  (151 F)

Flammable Limits (Approximate volume % in air):   LEL:  0.7     UEL: 5.3

Flammability (Solid, Gas):  N/A 

Autoignition Temperature:   >200 C  (392 F)

Boiling Point / Range:    183 C (361 F) -  208 C (406 F)

Vapour Density (Air = 1):   > 1 at 101 kPa

Vapour Pressure:    0.07 kPa (0.52 mm Hg) at 20 °C  |  0.5 kPa (3.75 mm Hg) at 50 C

       |  0.24 kPa (1.8 mm Hg) at 38 C

Evaporation Rate (n-butyl acetate = 1):    0.05

pH:   N/D

Log Pow (n-Octanol/Water Partition Coefficient):   N/D

Solubility in Water:   Negligible

Viscosity:   1.3 cSt  (1.3 mm2/sec) at 40 C  |  1.64 cSt  (1.64 mm2/sec) at 25 C

Freezing Point:   <-50 C  (-58 F)

Melting Point:   N/D

Decomposition Temperature:  N/D

Oxidizing Properties:  See Hazards Identification Section.

 

OTHER INFORMATION

 

Molecular Weight:    170

Coefficient of Thermal Expansion:   0.00094 V/V/DEG C

 

 SECTION 10

 STABILITY AND REACTIVITY

 

STABILITY:  Material is stable under normal conditions.

 

CONDITIONS TO AVOID:  Open flames and high energy ignition sources.

 

MATERIALS TO AVOID:   Strong oxidisers

 

HAZARDOUS DECOMPOSITION PRODUCTS:  Material does not decompose at ambient temperatures.

 

POSSIBILITY OF HAZARDOUS REACTIONS:  Hazardous polymerization will not occur.

 

SECTION 11

 TOXICOLOGICAL INFORMATION

 

INFORMATION ON TOXICOLOGICAL EFFECTS

 

Hazard Class

 Conclusion / Remarks

Inhalation

 

Acute Toxicity: (Rat)  8 hour(s) LC50 > 5000 mg/m3 (Vapour)

Minimally Toxic. Based on test data for structurally similar materials. Test(s) equivalent or similar to OECD Guideline  403

Irritation: No end point data for material.

Negligible hazard at ambient/normal handling temperatures.

Ingestion

 

Acute Toxicity (Rat): LD50 > 5000 mg/kg

Minimally Toxic. Based on test data for structurally similar materials. Test(s) equivalent or similar to OECD Guideline  401

Skin

 

Acute Toxicity (Rabbit): LD50 > 5000 mg/kg

Minimally Toxic. Based on test data for structurally similar materials. Test(s) equivalent or similar to OECD Guideline  402

Skin Corrosion/Irritation: Data available.

May dry the skin leading to discomfort and dermatitis. Based on test data for structurally similar materials. Test(s) equivalent or similar to OECD Guideline  404

Eye

 

Serious Eye Damage/Irritation: Data available.

May cause mild, short-lasting discomfort to eyes. Based on test data for structurally similar materials. Test(s) equivalent or similar to OECD Guideline  405

Sensitisation

 

Respiratory Sensitization: No end point data for material.

Not expected to be a respiratory sensitizer.

Skin Sensitization: Data available.

Not expected to be a skin sensitizer. Based on test data for structurally similar materials. Test(s) equivalent or similar to OECD Guideline  406

Aspiration: Data available.

May be fatal if swallowed and enters airways.  Based on physico-chemical properties of the material.

Germ Cell Mutagenicity: Data available.

Not expected to be a germ cell mutagen. Based on test data for structurally similar materials. Test(s) equivalent or similar to OECD Guideline  471  473  474  476  478  479

Carcinogenicity: Data available.

Not expected to cause cancer. Based on test data for structurally similar materials. Test(s) equivalent or similar to OECD Guideline  453

Reproductive Toxicity: Data available.

Not expected to be a reproductive toxicant. Based on test data for structurally similar materials. Test(s) equivalent or similar to OECD Guideline  414  421  422

Lactation: No end point data for material.

Not expected to cause harm to breast-fed children.

Specific Target Organ Toxicity (STOT)

 

Single Exposure: No end point data for material.

Not expected to cause organ damage from a single exposure.

Repeated Exposure: Data available.

Not expected to cause organ damage from prolonged or repeated exposure. Based on test data for structurally similar materials. Test(s) equivalent or similar to OECD Guideline  408  413  422

 

 

OTHER INFORMATION

             For the product itself: 

 

Vapour concentrations above recommended exposure levels are irritating to the eyes and the respiratory tract, may cause headaches and dizziness, are anaesthetic and may have other central nervous system effects.  Prolonged and/or repeated skin contact with low viscosity materials may defat the skin resulting in possible irritation and dermatitis.  Small amounts of liquid aspirated into the lungs during ingestion or from vomiting may cause chemical pneumonitis or pulmonary edema.

 

 

 

 

 

The following ingredients are cited on the lists below:  None.

 

 

--REGULATORY LISTS SEARCHED--

 1 = NTP CARC

 3 = IARC 1

 5 = IARC 2B

 2 = NTP SUS

 4 = IARC 2A

 6 = OSHA CARC

 

 

 SECTION 12

 ECOLOGICAL INFORMATION

 

 The information given is based on data available for the material, the components of the material, and similar materials.

 

ECOTOXICITY   

             Material -- Not expected to be harmful to aquatic organisms.

             Material -- Not expected to demonstrate chronic toxicity to aquatic organisms

 

MOBILITY

             Material -- Highly volatile, will partition rapidly to air.  Not expected to partition to sediment and wastewater solids.

 

PERSISTENCE AND DEGRADABILITY

Biodegradation:

             Material --  Expected to be inherently biodegradable

Hydrolysis:

             Material -- Transformation due to hydrolysis not expected to be significant.

Photolysis:

             Material -- Transformation due to photolysis not expected to be significant.

Atmospheric Oxidation:

             Material -- Expected to degrade rapidly in air

 

 

OTHER ECOLOGICAL INFORMATION

VOC:   Yes  

 

 

 

 

 

 SECTION 13

 DISPOSAL CONSIDERATIONS

 

Disposal recommendations based on material as supplied.  Disposal must be in accordance with current applicable laws and regulations, and material characteristics at time of disposal.

 

NATIONAL CATALOGUE OF HAZARDOUS WASTES

 HW06 - Organic Solvents Wastes and waste containing organic solvents

 

 

DISPOSAL RECOMMENDATIONS

 Product is suitable for burning in an enclosed controlled burner for fuel value or disposal by supervised incineration at very high temperatures to prevent formation of undesirable combustion products.

 

 Empty Container Warning Empty Container Warning (where applicable):  Empty containers may contain residue and can be dangerous.  Do not attempt to refill or clean containers without proper instructions.  Empty drums should be completely drained and safely stored until appropriately reconditioned or disposed.  Empty containers should be taken for recycling, recovery, or disposal through suitably qualified or licensed contractor and in accordance with governmental regulations.  DO NOT PRESSURISE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION.  THEY MAY EXPLODE AND CAUSE INJURY OR DEATH.

 

 SECTION 14

 TRANSPORT INFORMATION

 

China List of Dangerous Goods (GB 12268 - 2012) :  Not Regulated for Land Transport

   

 

[Footnote:  Regulated as Category 5 Class 2 under the Dangerous Goods Regulation for Hong Kong.]

 

INTERNATIONAL CLASSIFICATION FOR TRANSPORT

SEA (IMDG):   Not Regulated for Sea Transport according to IMDG-Code

     

Marine Pollutant:   No     

 

SEA (MARPOL 73/78 Convention - Annex II)

Product Name:  NOXIOUS LIQUID, N.F.,(7) N.O.S., (ISOPAR L, contains iso-and cycloalkanes (C12+))

Ship type:  3

Pollution category:  Y

 

AIR (IATA):   Not Regulated for Air Transport

           

 

 SECTION 15

 REGULATORY INFORMATION

 

The hazard classification for this material is in accordance with the General Rules for Classification and Hazard Communication of Chemicals (GB 13690-2009).

 

REGULATORY STATUS AND APPLICABLE LAWS AND REGULATIONS

 

The General Rules for preparation of precautionary label for Chemicals (GB 15258-2009):    Regulated

 

Law of the People's Republic of China on Prevention and Control of Environmental Pollution by Solid Waste:  See Disposal Considerations section.

 

Listed or exempt from listing/notification on the following chemical inventories:   AICS, DSL, ENCS, IECSC, KECI, PICCS, TCSI, TSCA

 

 

 SECTION 16

 OTHER INFORMATION

 

N/D = Not determined, N/A = Not applicable

KEY TO THE H-CODES CONTAINED IN SECTION 3 OF THIS DOCUMENT (for information only):

H227: Combustible liquid; Flammable Liquid, Cat 4

H304: May be fatal if swallowed and enters airways; Aspiration, Cat 1

 

THIS SAFETY DATA SHEET CONTAINS THE FOLLOWING REVISIONS:

 

Hazard Identification: US - Hazards Statement - GHS information was modified.

Section 07: Handling and Storage - Handling information was modified.

Section 07: Suitable Containers information was modified.

Section 13:  National Catalogue fo Hazardous Wastes information was modified.

 

 

  

 

 
[ 点击数:] [打印本网页] [关闭本窗口]  
 
相关内容
查无记录
 
网站管理